TM 5-3815-228-12&P
SECTION I
(5) Part numbers for bulk materials are referenced in this column in the line item entry for item the
manufactured/fabricated
(6) When the item is not used with all serial numbers of the same model, the effective serial numbers are shown
on the last line(s) of the description (before UOC). Not applicable
(7) The usable on code, when applicable (see paragraph 5, Special information) (8)
(8) In the Special Tools List section, the basis of issue (BOI) appears as the last line(s) in the entry for (each
special tool, special TMDE and other special support equipment. When density of equipment’s supported exceeds
density spread indicated in the basis of issue, the total authorization is increased proportionately.
(9) The statement "END OF FIGURE" appears just below the last item description in Column 5 for a given figure
in both Section II and Section III
f.
QTY (Column (6)). The QTY (quantity per figure column) indicates the quantity of the item used in the breakout
shown on the illustration figure, which is prepared for a functional group, subfunctional group or the figure where the item
is identified/located in Section an assembly. A "V" appearing in this column in lieu of a quantity indicates that the quantity
is variable and the quantity may vary from application to application.
4.
Explanation of Columns(Section IV)
a.
NATIONAL STOCK NUMBER (NSN) INDEX
(1)STOCK NUMBER column. This column lists the NSN by National item identification number (NIIN) sequence.
The NIIN consists of the last nine
NSN
digits of the NSN (i.e., 5305-01-674-1467)
NIIN
When using this column to locate an item, ignore the first 4 digits of the NSN. However, the complete NSN should be
used when ordering items by stock number.
(2) FIG. column. This column lists the number of, the figure where the item is identified/located in Section II and
Section III
(3) ITEM column. The item number identifies the item associated with the figure listed in the adjacent FIG.
column. This item is also identified by the NSN listed on the same line. column firm, corporation or Government activity),
which the item number is that
b.
PART NUMBER INDEX. Part numbers in this are listed by part number in ascending alphanumeric sequence
(i.e., vertical arrangement of letter and number combination which places the first be letter or digit of each group in order
A through Z, followed by the numbers 0 through 9 and each following letter or digit in like order.)
(1) CAGEC column. The Commercial And Government Entity (CAGE) Code (C) is a 5 digit alphanumeric code
used to identify the manufacturer, distributor or Government agency, etc., that supplies the item.
(2) PART NUMBER column. Indicates the primary number used by the manufacturer (individual, firm,
corporation or Government activity), which controls the design and characteristics of the item by means of its engineering
drawings, specifications standards, and inspection requirements to identify an item or range of items
(3) STOCK NUMBER column. This column lists the NSN for the associated part number and manufacturer
identified in the PART NUMBER and CAGEC columns to the left.
(4) FIG. column. This column lists the number of the Figure where the item is identified/located in Section II and
Section III.
(5) ITEM column The item number assigned to the item as it appears in the figure referenced in the adjacent
figure number column.
c.
FIGURE AND ITEM NUMBER INDEX
(1) FIG. column. This column lists the number the figure where the item is identified/located in Section II and III.
(2) ITEM column. The item number assigned to the item as it appears in the figure referenced in the adjacent
figure number column.
(3) STOCK NUMBER column. This column lists the NSN for the item.
(4) CAGEC column. The Commercial and Government Entity (CAGE) Code (C) a 5 digit alphanumeric code
used to identify the manufacturer, distributor or Government agency, etc., that supplies the item
(5) PART NUMBER Indicates the primary number used by the manufacturer (individual,
firm, corporation
or Government activity), which controls the design and characteristics of the item by means of its engineering drawings,
specifications standards, and inspection requirements to identify an item or range of items
A-4
